The APX Dual E2 CE Interface Module enables E2 G.703 8Mbps non-ATM equipment, such as a Microwave link, to be converged with other services using the AP multi-service platform.
This E2 CE module offers two protocol transparent, point to point connections to other E2 CE modules across an ATM network, leased line or transparent circuit (e.g. a satellite link).
This module performs adaptation of the incoming bit stream using unstructured AAL.1 to segment it into ATM cells. These ATM cells are transported across the AP infrastructure to the far end equipment. The far end AP, recovers the ATM cell stream, and from this re-assembles the E2 G.703 8Mbps bit stream, again using unstructured AAL.1. End to end timing is automatically maintained through the use of adaptive clocking and jitter attenuation.
Management and configuration of this module is achieved via the simple menu driven user interface. Extensive statistics and status information are available to the user interface as a diagnostic aid. Additionally SNMP Traps may be generated to indicate Link Up/Down. These modules can be "Hot Swapped" to ease maintenance, with replacement modules recovering immediately without further configuration.
This module has the following features:
- 2 independant standards compliant E2 G.703 8Mbps interfaces with 75 ohm BNC connectors
- can be used in any AP chassis
- hot swap interface module, with configuration automatically loaded onto the replacement module
Module Specifications |
|
| Description |
Dual E2 BNC CE Module |
| Ports | 2 |
Physical Layer |
|
| Data Rate | E2, 8.448Mbps |
| Physical | BNC pair, 75 ohm |
| Line Code | G.703, HDB3 |
| Framing | Unstructured |
| Clocking | Adaptive |
| Jitter | G.823 |
| Alarms | LOS, AIS, TXUR |
ATM Layer |
|
| Adaptation | ITU I.363 AAL.1 |
| Cell Rate | 22469 cells/sec |
| Bandwidth | 9.53Mbps |
Approvals |
|
| Conformance | ITU I.363 AAL.1 |
| MIB 2 RFC1213, RFC1215 | |
| EN60950, EN55022, EN50082 | |
| Environmental | 0-40C, 0-95% RH Non Condensing |
| 86-106kPa |
Product |
Order Code |
| Dual E2 CE |
80-07-304 |
AP Circuit Emulation Interface Modules
The following circuit emulation interface modules are available for the AP platform:
- Quad T1 CE module - legacy services at 1.5Mbps Telecom rates, e.g. North American leased lines.
- Quad E1 CE module - legacy services at 2Mbps Telecom rates, e.g. PBX, E1 G.703 2Mbps leased lines.
- Dual E1 CE module - legacy services at 2Mbps Telecom rates, e.g. PBX, E1 G.703 2Mbps leased lines.
- Dual E2 CE module - legacy services at 8Mbps Telecom rates, e.g. E2 G.703 8Mbps leased lines.
- E3 CE module - legacy services at 34Mbps Telecom rates, e.g. E3 G.703 34Mbps leased lines.
- DS3 CE module - legacy services at 45Mbps Telecom rates, e.g. DS3 G.703 45Mbps leased lines.
- 10/100BaseT LAN CE module - transparently bridges 10/100BaseT LANs.
- EIA530 CE module - serial data streams (of up to 20Mbps), e.g. router serial cards, encrypted data and satellite modems.
- HSSI CE module - serial data streams (of up to 110Mbps), e.g. router serial cards, encrypted data and satellite modems.
- ECL CE module - serial data streams (of up to 110Mbps), e.g. router serial cards, encrypted data and satellite modems.
- ASI CE module - broadcast video data streams (of up to 52Mbps), e.g. video codecs, satellite modems and broadcast infrastructure.
AP Overview Page
- AP - overview of Access Processor family of chassis and interface modules.
